|
|||||||||||||||||||||||||||||||
Single-*ponent Water Based Spray Adhesive for Sponge HN-828
Introduction:This adhesive is water based, non-toxic and environmentally friendly. It has long open time, fast drying speed, strong initial bonding strength, and it is heat resistant and anti-aging.
Besides, it can be used by single-side or double side spray method.
With the above features, it’s especially suitable for bonding sponge to sponge in making high-end soft furniture.
Properties:
Appearance: Milky white liquid
Solid Content: 50±2%
Viscosity: 200-500cps（25℃）
Working Condition: Temperature between 4-45℃, relative humidity under 80%
Bonding Time: Bond the material after 2~3 minutes
Transportation and Storage Temperature: 5-45℃
Odor: None
Strength: The biggest bonding strength is achieved after the glue cured 24 hours later
VOC: No volatilization
Quality Guarantee Period: 6 months
*pliance with Environmental Requirements
This adhesive contains no hazardous substance which has strict limit by the rule GB18583Limitation on Hazardous Substance in Adhesive for Interior Decoration Materials, and VOC is less than 50g/L, which *plies with the environmental requirements by ROHS and REACH. This product has obtained the SGS certification.
Note:
1. Avoid direct contact with eye. Please wash with plenty water if the product is spattered into your eyes.
2. Avoid exposure to the sun and frost while the product is in storage, transportation or application. Tightly seal up the product after use to prevent surface crusting.
FAQ and Solution to Water Based Spray Adhesive:
|
FAQ |
Possible Causes |
Solution |
|
Weak or no initial bonding strength |
Slow evaporation on adhesive |
Change the working process |
|
Temperature is so low that initial bonding strength is affected. |
Adjust the temperature in working field. |
|
|
The adhesive layer is so thick that causes slow drying speed. |
Adjust the spraying amount based on the correct operation. |
|
|
The adhesive layer is so thin that causes shortage of gel. |
Adjust the spraying amount based on the correct operation |
|
|
Failure to spray |
Low air pressure |
Adjust the air pressure to normal state, 2.5-8kg. |
|
Spray nozzle is stuck by gel |
Clean out the gel from the nozzle by wet towel or finger. |
|
|
Malfunction of spray gun |
Change or fix the spray gun. |
|
|
Uneven spraying |
Low air pressure |
Adjust the air pressure to normal state, 2.5-8kg. |
|
Malfunction of spray gun |
Change or fix the spray gun. |
|
|
Spray distance is too far. |
Adjust the spray distance and angle. |
|
|
Adhesive viscosity is too high |
Addpurified waterto adjust the viscosity. |
|
|
Too misty when spraying |
Spray distance is too far. |
Adjust the spray distance and angle. |
|
High air pressure. |
Lower the air pressure |
|
|
Too scattered when spraying |
Adjust the sector-like spraying method to straight-line one. |
|
|
No air evaporation equipment |
Install air evaporation equipment to remove the unwanted mist. |
|
|
defect of spray gun |
Use spray gun with bigger nozzle. |
|
|
Debonding with material partly stick together
|
Uneven spay causes pile-up of gel |
Adjust the air pressure and distance of spray gun, and spray evenly. |
|
Uneven spray causes shortage of gel |
Adjust the air pressure and distance of spray gun, and spray evenly. |
|
|
Bond without thoroughly drying (mainly occurs in winter and rainy season). |
Bond the material after the adhesive surface dries. It takes 2~3 min. Use oven in wet weather. |
|
|
Stress is not put on all parts of the material. |
Stress on the material evenly. |
|
|
Bond after the best bonding timing. |
Bond the material within the best bonding time. |
Clearance of Spray Gun
Pour out the adhesive from the spray can after use and use tap water to clean it. Then fill in the can with water and spray it out to clean the absorption tube and the gun inner. Alternatively, you can detach pneumatic tube, fill the absorption tube with water, and press the trigger to let the water flow out until the flowing water is as clean as the tap water.
*parison of properties between Water Based Spray Adhesive and Solvent Based Spray Adhesive
|
Number |
Item |
Solvent Based Spray Adhesive |
Water Based Spray Adhesive |
|
1 |
Appearance |
Light yellow or brown yellow |
Milky white |
|
2 |
Solid Content |
約30% |
50±2% |
|
3 |
Spray area per kilogram of adhesive |
|
|
|
4 |
Spray amount per 100㎡ |
|
|
|
5 |
Spray ability |
Large spray amount; double-side spray |
Proper spray amount; double-side spray |
|
6 |
Viscosity |
SBS type:＜150cps Cr type:＜400cps |
200-500cps/25℃ |
|
7 |
Solvent |
Organic solvent: benzene, ketones |
Deionized water |
|
8 |
VOC |
>65% |
0 |
|
9 |
Odor |
Solvent odor |
No Odor |
|
10 |
Viscosity |
Achieve the largest strength after 4 hours |
Achieve the largest strength after 24 hours |
|
11 |
Spray distance |
50-80cm |
20-40cm |
|
12 |
Drying time |
Edge-fold: 1min. PVC leather: 1min Thick leather: 2min-3min |
Edge-fold:≥2min PVC leather: 2min-3min Thick leather: 2min-3min |
|
13 |
Repeated bonding times |
2-3 times |
2-3 times and more if adhesive layer is thicker. |
|
14 |
Bonding time |
Within 30s after adhesive dries |
Within 20-30s after adhesive dries |
|
15 |
Specification of spray gun |
F75, small spray gun PQ-2 |
Inquire the technician |
|
16 |
Material’s movability after bonding (It can be turned to next process directly.)
|
It can be turned to next process directly under normal circumstances.
|
It can be turned to next process directly under normal circumstances. |
|
17 |
Heat resistance |
50-60℃
|
80-90℃ |
|
18 |
Product Standards |
GB-18583 2008 national certification |
GB-19340 2003 SGS certification |
|
19 |
Safety performance on fire-proof |
Potential safety hazard caused by fire |
Do not havepotential safety hazard caused by fire |
單組份環保水性噴膠——海綿專用膠
水性噴膠型號：828
產品特性：本產品屬高效水溶性膠粘劑，具有無毒不燃、綠色環保、開放時間長、干燥速度快、初粘性強、耐熱性和防老化能力俱佳等優點。
產品用途：使用于海綿粘海綿的高檔軟體家具的制造，且可單面噴膠粘合。
水性噴膠產品參數：
外觀：乳白色液體
固含量：50±2%
粘度：200-500cps（25℃）
施工條件：溫度4-45℃，相對濕度低于80%
晾膠時間：2-3分鐘以后貼合
運輸和儲藏溫度：5-45℃
氣味：無
強度：膠水固化24小時后拉力最大
VOC：揮發量為零
保質期：6個月
產品符合環保要求：
不含GB18583《室內裝飾裝修材料膠粘劑中有害物質限量》中有害物質，總揮發性有機物含量小于50g/L，符合歐洲ROHS和REACH環保標準，本產品已通過SGS的認證。
注意事項：
1、 避免該產品與眼睛直接接觸，如不慎濺入眼睛，請馬上用清水沖洗。
2、 產品在儲存、運輸和使用過程中需防止太陽暴曬和霜凍、膠水使用后應密封好包裝桶，以防止膠水結皮而影響施工。
